Statement
This HUIDU HDSet Operating manual is just for reference only, if you have any problems during using this LED display control software or have any questions about this operation document, please contact the HUIDU tech department.
HDSet Operating Manual
Here is the HUIDU HDSet operating manual to help you know more about how to use HDSet LED Control software, this opeartion & guide includes software installation and uninstallation, detect device, setting paramenters, smart setting, firmware updating, screen testing, etc
- V2.0 20200205
Software installation
Double-click the software executable file HDSet.exe directly, and follow the software prompts to install it by default. You can download the HDSet in here.
Detect device
- T901/VP210/VP410 is connected to the computer using a dedicated USB cable;
- The software will automatically detect the device when open.
- When the device is found, the device is listed on the left list and the device information if the mouse moves on the device.
Setting Hardware parameters
Sending card parameter settings can be set resolution, frame selected mode (60Hz / 30Hz) selection, receiving card type (Huidu or other receiving cards), audio transmission, automatic brightness, uniform brightness, receiving card detection, and other functions. adjustment of network port, receiving, and other functions.
Note 1) one RJ45 port →1280×512@60Hz, 1280×1024@30Hz； 2) Audio module and automatic brightness adjustment need to be used with multi-function card Y1.
- Click on the ‘connection settings’ and enter the ‘connection Settings ‘interface
- This page is divided into ‘Standard’ settings and’ profession’ settings. It is convenient and quick to set the connection relationship of the receiving card, when looking from the front of the screen, the first receiving card connect is card number 1, and so on. Multiple network ports can be set.
- Introduction of icons in connection setting interface：
- Introduction of icons in connection setting interface：
- Full-screen edit connection relationship；
- Read back: readback connection settings
- Add cabinet: click and drag in the box setting interface for a long time to
add multiple cabinets.v - Delete cabinet: Click to delete the selected cabinet;
- Delete cabinets
- Restore button: Click to restore the previous steps.
- Combined button: select multiple cabinets and click them. The selected cabinet becomes a whole
- Button for canceling combination: after canceling the combination, each
cabinet becomes a box that can be set separately. - Erase button: clear cabinet information
- Hide/show cabinet: click it to hide or show all cabinets of the selected network port.
- Hide route: click it to hide or show the route of the connection relationship
- Cabinet proportion: adjust the cabinet proportion to facilitate operation
Notes
- The connection relations of all network ports are set together, and the sending parameters do not distinguish between network ports.
- The import and export do not distinguish between network ports. When the parameters exported by the old version of the software are imported into the control card with multiple network ports in the new version of the software, only the connection relationship and receiving card parameters of network port one are imported. The connection relationship of other network ports needs to be adjusted manually. No other settings are required for the control card imported to the single network port.
- Network port division of the old version. The network port is loaded on the interface of the new version of the connection relationship
- Add the setting parameters of the specified receiving card (right-click the box to select the receiving card parameters to enter the specified receiving card setting interface). A30, cx0, and CX5 series sending cards cannot modify the sending card itself as the parameters of the receiving card.
- Receiving card parameter setting:
Click ‘receiving card parameter’ to enter the receiving card parameter setting interface. this interface is for the gray level, refresh rate, PWM register parameter settings, the parameters of this interface directly affect the effect of the LED display screen.
- Universal module interface of can set up the common module quickly
- Smart setting： for the common module, if there is no corresponding configuration file in ‘Universal module’, the module parameters can be set by ‘Smart setting’.——For details, see section 2.3.
- Advanced setting: In this interface, you can adjust the gamma, color correction, and other parameters to further adjust the effect of the LED screen display.
- Color channel: the red, green, and blue colors of the display can be changed through debugging.
- Data Group Exchange： this function can exchange output data from one port to another port.
- Extended mode： for some special IC, such as high refresh rate IC. Register configuration is required to set up with this function.
- Data group offset: mainly used for special irregular screen or cross-screen.
Smart setting
- The following figure is the first step for the Smart setting. In this interface need to set, the screen color type, single module width(in pixel), module chip type, and decoding mode (drop-down options are: 138 decode, non-decoding, 595 decode, 5958 decode, etc.). If the module is larger than 16 scans, please check ‘More than 16’， If the module is larger than 32scan, please check ‘More than 32’
- The figure below shows the second step of smart settings. In this step, please try to select A B to see if the module is fully lit. Select the corresponding option in the display state according to the module performance. This step is to determine the data polarity.
- The figure below shows the third step of smart settings. At this step, please try to select A B to observe the brightness of the module. According to the performance of the module, select the corresponding option in the display state. This step is to determine the OE polarity.
- The following figure shows the fourth step of smart settings. At this step, please try to select the status A, B, C, D to observe the color display of the module. According to the module performance, select the corresponding option in the display status. This step is to determine the color channel of the module
- The figure below shows the fifth step of smart settings. Please observe the performance of the module and fill in the corresponding values. This step is to test the height of a set of RGB controls.
- The figure below shows the sixth step of smart settings. Please observe the performance of the module and fill in the corresponding values. This step is to test the scan type.
- The figure below shows the seventh step of smart settings. Please observe the module performance and click the corresponding cell according to the location of the flashing point.
After you finish, click Save to complete the smart settings.
Auxiliary function
1. Firmware Updating
- Click firmware upgrade and the password is 888. Enter the interface of sending card upgrade, select the corresponding firmware, and then click upgrade. Select all the corresponding firmware in the interface of receiving card parameters. Click upgrade (download the corresponding controller firmware, each product has the
2. Screen Testing
- For LED screen test, including color, gradient, aging test, scan, positioning.
3. More languanges
- Click【language】 in the upper right corner to adjust the display language
- Click to bring up the following interface,password is 168.
4. Other Settings
- Point-by-point correction, use for correcting the brightness of each pixel/module on the LED screen;
- Multi-function card, used with multi-function card YI, mainly including relay setting (on/off the power of the screen), detecting the temperature/humidity of the box body, and so on;
- Hidden function trial lock, also known as engineering lock, is used for timeout lock setting. Shortcut key (FN + F9)
After HDSet has set the screen ok, use HDShow to edit and play the program. Know how to use please check the HDShow operation manual.